Anodised CNC Seatclamp
€5CNC Seatclamp Anodised in Red or Black.
Collar height 11mm
Straight forward seatclamp
Available in 25.4mm / 28.6mm / 31.8mm / 34.9mm
Showing 1–12 of 15 results
CNC Seatclamp Anodised in Red or Black.
Collar height 11mm
Straight forward seatclamp
Available in 25.4mm / 28.6mm / 31.8mm / 34.9mm
Short stubby lightweight Carbon bar ends
weight for pair = 114g
Length approx 70mm from bar.
Clear specialist high impact protection tape to protect your frame from scratches.
Frame tape comes in a roll
10cm x 150cm
(3.9 inches x 59inches)
Super tough stickers.
12 Clear specialist high impact/modulus protection stickers to protect your frame from scratches.
1 Large Clear protection 92mm W X H X L
1 Clear chainstay protector 230mm (long) x 31 (width)
5 Round (30x30mm) Protectors
5 Oval Shaped (50 x 20mm Protectors)
CNC Machined Bottle opener quick release bolt for seat clamps.
– available in Red, Green, Orange, Gold, and Black
Chain tug rear derailleur hanger adapter for horizontal drop outs and dirtjumper frames (or singlespeeds)
If you need to add a derailleur to your dirtjump bike or singlespeed this is what you need!
They are keyed for 10mm dropouts with 10mm axle hole
Chain Device for a Double Chainring setup.
This device is compatible with 22-44 tooth rings
– Available for ISCG-05 Only
– CNC machined 6061 T6 aluminium backplate.
– Sealed bearings inside roller for smooth running.
– Available in black .
All Bolts and spacers are supplied for fitting.
Chain Device for a Single Chainring setup.
This device is compatible with 22-44 tooth rings
– Sealed bearings inside roller for smooth running.
– Available for both ISCG-05 and ISCG old (ISCG ’03)
– CNC machined 6061 T6 aluminium backplate.
– Available in black only.
Bolts and washers are supplied to fit the guide.
Brand New Just in!!! Narrow Wide chainrings available in either Anodised Black and Red.
These rings have machined teeth to fit into the links on any 9, 10 or 12 speed chain. The clever machined teeth, combined with a clutch-equipped derailleur will keep your chain from bouncing off of the front ring.
Offset bushings to slacken you headangle. These are an initial batch produced for us by Kevin Coughlan.
= MORE INFO TO FOLLOW = WE JUST PUT THESE UP.
– Fit ½” shock eyelets ( Fox, Marzocchi, Rock Shox from ’08)
– Made from 6082 T6 aluminium
– Polished Finish.
The average DH bike with M8 bolts a 3inch stroke shock and 9 inches of travel will get about a 0.5inch BB drop and about 1 – 1.5 degree slacker HA.
The bushes are made of 6082 T6 alu. This means it’s a hard surface and the type of alu is very stiff with no flex.
Hard surface means corrosion resistant and long wear life.
Each bush is ground/sanded and polished for smoothest surface finish and lowest friction
Bushing sizes currently available.
19mm x m6
25.4mm x m6
22mm x m6
22mm x m8
25.4 x m6
30mm x m8
Beautifully made CNC machined aluminum clamp. The lever operates smoothly and holds the post securely. The size is not the same as seat post size but frame diameter, Measure the exterior diameter of your seat tube (on your frame) to determine the proper size.
– Available in 2 sizes 34.9 and 31.8
– available in Red, Green, Blue, Orange, Gold, Pink, Purple and Black
No products in the cart.